Summary:
Spray
n Seal is a water-based penetrating sealer that protects natural stone surfaces
from staining. It is wonderful for stone countertops, floors, walls, vanities
and even grout. This below surface sealer is also ideal for sealing all types
of masonry, stucco, and concrete. It has a special blend of polymers that bond
to the stone and creates a water and oil repellent membrane to prevent
staining, yet it allows the stone to breathe and release moisture vapors. It is
safe for interior and exterior use and is UL Classified for slip resistance. Spray
N Seal is safe to use on food handling surfaces.
Spray n Seal is available in a quart and 8oz. container. We also have the
Spray-n-Seal XP for an Extra Porous Surfaces.
Preparing your surface:
All surfaces must be clean and free from debris and remain dry for 6-12 hours
before the application of STONE SPRAY N SEAL and remain dry for 24-48 hours
after the application.
48
Hours provides the best protection.
Floor surface temperature must be above 50 degrees F and below 90 degrees F.
Smooth Polished or Smooth Honed Surfaces: Countertops, Floors, Vanities,
& Walls:
Always test first in a small area for desired
results before applying to entire surface.
If your surface has any topical waxes
or stains, they must be removed before sealing.
Clean countertop surface using Marbamist
or Clean
EnCounters.
For
stone floors, clean with Marbalex.
(It is safe to lightly clean the stone before sealing.)
Surface should be dry for 6-12 hours
before sealing.
Cover surrounding areas that are not
intended to be sealed.
Liberally spray the entire surface
until it is wet. (Outer edges may dry quicker.)
When surface begins to dry within 3-5
minutes, wet the surface again with the sealer.
(This will allow the sealer to properly penetrate and cure.)
After 30 minutes, wipes off excess
sealer from the surface with a clean & dry white terry cloth towel.
If excess dries on the surface, spray
more sealer onto the surface and wipe off immediately with a
clean dry terry cloth towel. For large stone floors, excess can be buffed off
with a clean white buffing pad or an all
cloth bonnet pad.
Floor surfaces may be walked on 4 hours
after application. For best curing results, keep surface dry for 24- 48 hours
after application. 48 hours will provide best protection.
Grout Sealing:
Grout must be dry for 72 Hours. Liberally spray the grout until it is wet. Wipe
off excess sealer with a white terry cloth towel, 3 minutes after application.
Grout Release:
Install the stone with the proper setting materials and follow procedures A-G.
Apply grout to the joints. Wipe off remaining residue with MARB
ALEX or MARBAMIST . Seal
sanded grout 72 hours after curing.
Routine Maintenance:
General cleaning of floor surfaces use Marbalex General cleaning of
countertops, tabletops, vanities and walls use MARBAMIST
or CLEAN
ENCOUNTERS.
Applications:
Granite
Marble.
Slate
Terra Cotta
Limestone
Terrazzo
Agglomerates
Concrete
Ceramic & Porcelain Tile
Brick
Textures/Surfaces:
Polished
Honed
Flamed/Thermal
Tumbled
Cross Cut
Bush Hammered
Sawn
Technical Data/ Benefits:
Colorless
Non-staining.
Water based
UV Transparent
Acid and Alkali resistant
Non-yellowing
Permeable
Substrate Penetrate
Non-Flammable
Ideal for all textures
Ideal for all types of stones
UL Classified for slip resistance
Provides excellent stain protection.
Acts as an excellent grout release.
Prevents the growth of bacteria, mold
and mildew on interior and exterior stone.
Simple to apply and user friendly.
Helps prevent adhesion and penetration
of fluids and dirt.
Safe for contact of membranes.
Approximate Coverage Sq. Ft. Gallon Container:
Polished Marble 2,800
Flamed Granite 800
Slate 1,800
Limestone 800
Terra Cotta 1,100
Polished
Granite 2,500
Agglomerates 4,200
Mexican Pavers 700
Residential Care /Full Line Product
Demonstration
Recommendations:
Always test a small area before using
to determine if the product is applicable
All stains, moisture, and dirt must be
removed prior to the sealer application and must remain dry 24-48 hours after application.
The surface must be completely dry
before applying to the surface. Allow three hours after the Application before walking on the surface.